Impreza Wrx Sti

TD06 20G Turbo for Subaru WRX STI 02-07 EJ20 EJ25 Bolt On Turbo Charger

TD06 20G Turbo for Subaru WRX STI 02-07 EJ20 EJ25 Bolt On Turbo Charger
TD06 20G Turbo for Subaru WRX STI 02-07 EJ20 EJ25 Bolt On Turbo Charger
TD06 20G Turbo for Subaru WRX STI 02-07 EJ20 EJ25 Bolt On Turbo Charger
TD06 20G Turbo for Subaru WRX STI 02-07 EJ20 EJ25 Bolt On Turbo Charger
TD06 20G Turbo for Subaru WRX STI 02-07 EJ20 EJ25 Bolt On Turbo Charger

TD06 20G Turbo for Subaru WRX STI 02-07 EJ20 EJ25 Bolt On Turbo Charger

TD06 20G Turbo for Subaru WRX STI 02-07 EJ20 EJ25 Bolt On Turbo Charger. Fit Engine: 2002 WRX GC8 EJ20. 2002-current WRX / STI EJ20 EJ25. Compressor Wheel Diameter: 52.5 / 68 mm.

TURBINE Wheel Diameter: 49.2 / 56 mm. Turbine flange type flange: IHI (Subaru flange type). Downpipe flange type : wrx / sti 5 bolt. Cooling type : oil and water cooled. Actuator set at : 14 PSI. No core charge, Brand New. This is a direct bolt on aftermarket turbo. Same performance as the factory turbo parts with better price. Subaru TD06 20G Turbo Water Pipe Kit Fit WRX / STI. Subaru sti Turbp Impreza WRX VF48 Turbocharger Bolt On.

An 5% additional charge will be apply on American Express users. Parts must be in new, re-salable condition.

If a part arrives damaged, or is defective, we can help you to take care of it but it must be reported to us immediately. Please be patient if your inquiry requires further investigation. Business Hour: 8:30am - 5:00pm Monday through Friday. Once you have received your item, please leave feedback for us as this will inform us that you have received your items.

When re-installing the turbo, be sure that you take out any rags anything else you used to block off any inlets or intercooler hoses. Your old turbo's Demise.

But if you killed a fairly new turbo for no apparent reason, think about what could have been the cause of the turbo's failure. If you simply bolt on a new turbo without fixing the problem, don't expect your new turbo to live long either. There is a gap between the shaft and sleeve and a gap between the sleeve and housing. These two gaps combined allow the compressor wheel tip to move side to side in what may look like an alarming amount.

As long as the wheel is not touching the housing, you are fine. There should be no play axially (in and out) with the compressor wheel and shaft. You were doing some grinding or porting near the motor with the turbo removed. You blocked off the turbo oil drain pipe with a piece of tape.

You forget to take the piece of tape and install the turbo. Start it up and instant James Bond smoke.

The oil flow into the turbo has nowhere to go and gets pumped out the bearing seals. If your turbo does this, check the oil drain for blockage, remove it and start it up again. The turbo will be fine, it will take a few minutes of driving to burn out all the oil from the exhaust system. Also a plugged up crank case vent will cause excessive pressure to build up in the crankcase. This prevents the oil from draining out of the turbo and blows the excess oil out through the turbo seals. Listing and template services provided by inkFrog. The item "TD06 20G Turbo for Subaru WRX STI 02-07 EJ20 EJ25 Bolt On Turbo Charger" is in sale since Monday, December 21, 2015. This item is in the category "eBay Motors\Parts & Accessories\Car & Truck Parts\Turbos, Nitrous, Superchargers\Turbo Chargers & Parts". The seller is "turboking626" and is located in Alhambra, California. This item can be shipped worldwide.

  • Modified Item: No
  • Custom Bundle: No
  • Manufacturer Part Number: JM-SU-04 (1)
  • Placement on Vehicle: Front
  • Brand: JM Turbo Technology
  • Non-Domestic Product: No
  • Warranty: Yes


TD06 20G Turbo for Subaru WRX STI 02-07 EJ20 EJ25 Bolt On Turbo Charger